Deformation of Rodlike Elements of Composite Materials Subjected to Uniform Compression

On the basis of generalization of the results of investigation of the operation of rodlike elements of composite materials, we make a conclusion that the influence of various factors on the deformability of these elements is studied incompletely. The comparison of the stress-strain states for different models of concrete and reinforced-concrete elements makes it possible to describe the effect of longitudinal reinforcement (coefficient of reinforcement, strength and deformation characteristics) on the critical level of strains in the cross section. According to the results of our investigations, we give recommendations concerning the evaluation of the critical value of the coefficient of reinforcement above which one may observe the effect of reinforcement on the deformability of the analyzed sections. It is shown that the compression strength of the brittle base of the composite with inhomogeneous structure decreases as a result of the fracture processes. It is also demonstrated that the existing procedure used for the evaluation of the indicated decrease in strength requires significant improvement. The problem of evaluation of the ultimate value of the coefficient of reinforcement is also analyzed.     

Preparation of BaMgAl10O17∶Eu2+ and Its Phase Behavior in Microemulsion System

BaMgAl10O17∶Eu2 (BAM) was prepared in the microemulsion system and its phase behavior was studied. There exists a small region in the reverse microemulsion system where the dispersed particles are of spherical form. In this way, BAM blue phosphor with good dispersion can be synthesized. The microemulsion phase diagrams of the pseudo-ternary system (Triton X-100/cosurfactant-oil-BAM brine) were first established intuitively by the dilution method. The microstructure of microemulsions was determined through eyeballing, conductance technique, and polar optical microscopy. Its phase behavior is affected by various factors, such as temperature (room temperature, 30, 40 ℃), oil, surfactants, and cosurfactants in microemulsions. According to the phase diagrams, the microemulsion system of Triton X-100/1-hexanol-hexane-BAM brine was chosen to prepare the precursor. The BAM phosphor can be obtained via sintering the precursor at a comparatively low temperature. The phosphors were characterized by XRD and vacuum ultraviolet (VUV) spectra.     

丁集矿副井井架基础沉降变形分析

按井筒冻结施工的进度,选择合适的周期进行沉降变形观测,根据大量的实测资料对冻结施工前后丁集矿副井井架基础的沉降变形规律进行了分析,并预测其沉降变形趋势。     

Ready, Set, Go! The Voronoi diagram of moving points that start from a line

It is an outstanding open problem of computational geometry to prove a near-quadratic upper bound on the number of combinatorial changes in the Voronoi diagram of points moving at a common constant speed along linear trajectories in the plane. In this note we observe that this quantity is Θ(n²) if the points start their movement from a common line.     

红外隐身技术的现状与发展

综述了红外隐身技术的现状，指明了存在的问题以及发展的方向。     

Recrystallization/precipitation behaviour in microalloyed steels

Microalloyed high-strength low-alloy (HSLA) steels contain additions of Nb, V, Ti, or in combination, in amounts of 0.01 to 0.1 weight percent to improve mechanical properties, which are strongly dependent on the thermomechanical interaction taking place in the course of rolling mill processes. The recrystallizatian of hat-twisted austenite has been investigated in a cylindrical specimen (f 6×50 mm) machined from hat rolled plates of 0,052 wt % Niobium microalloyed steel. Continuous and interrupted torsion test were carried out in the temperature range 1123 K to 1173 K after a solution treatment of 1.5 minutes at 1423 K and torque-twist data were analysed. The various methods were discussed for obtaining results from torsion tests. The effect of precipitation kinetics was appreciated by way of connection t_p/t_p(red), where t_p is the experimental measured time for the peak stress and t_p(red) is the newly defined reduced time. The softening ratio X and time t_0.05R for start of static recrystallization were established.

The correlation between precipitation and recrystallization is presented as a graphs for chosen requirements (temperature of austenitization, carbon and niobium content and strain rate). If temperature goes below 850°C, the restoration processes are hardly suppressed, both are limited by diffusion and Nb(CN) precipitation, which are extended dynamically in the range of strains rates 10⁻² to 1 s⁻¹.

In the present paper, an attempt is made to derive the PRTT diagram and to define all mathematical equations for describing recrystallization times t_0.05R, t_0.5R, t_0.95R and t_0.05P for the start of precipitation. In real metal forming processes such as the hot rolling of plates or strips the knowledge of these parameters and results is extremely important for the the correct microstructure and sheet quality to be obtained.     

PPS：基于PROSITE数据库检索蛋白质功能位点的计算机程序

用标准Ｃ语言在ＩＢＭ－ＰＣ兼容微机上开发了基于ＰＲＯＳＩＴＥ数据库检索蛋白质序列功能位点的ＰＰＳ程序，ＰＲＯＳＩＴＥ是Ｂａｉｒｏｃｈ建立的蛋白质功能位点或结构模式的资料库，为蛋白质序列分析和结构功能研究提供了新工具。     

Prediction of liquid–liquid phase diagrams of aqueous salt+PEG systems using a thermodynamic model

In this study a thermodynamic model for the phase behavior of aqueous salt+polymer solutions is developed. The model is based on the solution theory of Hill, which included scaling laws for the polymer molecular mass dependence and Pitzer–Debye–Hückel theory. This model was tested for systems composed of two different molecular mass of polyethylene glycols (PEG) and five different inorganic salts. All the model parameters were determined from independent measurements. The agreement between the experimental and predicted phase diagrams by this model is good.     

热力学相图计算技术在闪速燃烧合成氮化硅铁中的应用

将热力学相图计算技术应用于Si-Fe-O-N体系,以评估由FeSi75粉闪速燃烧合成氮化硅铁的条件和目标产物。结果表明:将闪速燃烧温度控制在1200～1500℃之间较为适宜,此时平衡态产物中除主要含有Si3N4以外,还有一定量的Fe与Si间化合物和少量稳定的SiO2存在。此计算结果与实际试验结果吻合良好。     

集团变分法(CVM)及其在合金相图计算中的应用

介绍了集团变分法的集团概率变量、配置熵等统计分析的理论基础及Helmholtz自由能的描述模型.提出了巨势及相对化学势的几何分析理论.讨论了应用集团变分法和巨势分析理论进行相平衡计算的过程,并分析了同结构平衡相图计算的若干实例.